Machinery's Handbook for Machine Shop and Drafting-room: A Reference Book on Machine Design and Shop Practice for the Mechanical Engineer, Draftsman, Toolmaker and Machinist |
What people are saying - Write a review
Reviews aren't verified, but Google checks for and removes fake content when it's identified
User Review - Flag as inappropriate
Page no - 207
User Review - Flag as inappropriate
As essential to the shop as the CRC Handbook is to the lab. (and with a lot of overlapping info) The 1915 edition is far from useless, just as the periodic table of non-manmade elements or the melting point of sulfer hasn't changed since 1915, neither has much of this information.
Contents
| 1 | |
| 128 | |
| 297 | |
| 370 | |
| 386 | |
| 401 | |
| 447 | |
| 463 | |
| 494 | |
| 506 | |
| 519 | |
| 549 | |
| 607 | |
| 642 | |
| 700 | |
| 717 | |
| 756 | |
| 765 | |
| 828 | |
| 843 | |
| 876 | |
| 1201 | |
| 1207 | |
| 1213 | |
| 1220 | |
| 1265 | |
| 1272 | |
| 1294 | |
| 1304 | |
| 1334 | |
| 1365 | |
| 1371 | |
| 1383 | |
Other editions - View all
Common terms and phrases
allowable angle approximately assumed axis bearing belt body calculations cast iron cent circle circular column Cosine Cotangent cutter deflection depth Diam diameter diametral pitch dimensions direction disk distance divide drill driven edge equal example face factor feed feet feet per minute figures force formulas friction gear given gives grinding head holes increase lead length less load Logarithms lubricant machine material maximum milling minute multiply number of teeth obtained pinion pitch pitch diameter plate pounds pounds per square pressure pulley radius ratio rivets roll Root rope rule Screw Secant shaft side Sine speed spiral spring square inch steel strength stress surface Tangent thickness thread tool tooth turning varies weight wheel width Wire Worm
Popular passages
Page 255 - Moment of a Force. — The moment of a force with respect to a point is the product of the force multiplied by the perpendicular distance from the given point to the direction of the force.
Page 275 - If a body oscillates about an axis, then the point at which, if a blow is struck by the body, the percussive action is the same as if the whole mass of the body were concentrated at that point, is called the center of percussion. This point is located at the same point as the center of oscillation. Center Reamers. A "center reamer" is a reamer the teeth of which meet in a point.
Page 983 - Depth of Cut per Tooth The amount of metal that the successive teeth of a broach should remove, or the increase in size per tooth, depends largely upon the hardness or toughness of the material to be broached. The size of the hole in proportion to its length also affects the depth of cut, so that it is impossible to give more than a general idea of the increase in size per tooth. Medium-sized broaches for round or square holes usually have an increase of from 0.001 to 0.003 inch per tooth for broaching...
Page 291 - The time of vibration of a pendulum varies directly as the square root of the length, and inversely as the square root of the acceleration due to gravity at the given latitude and elevation above the earth's surface.
Page 270 - If a body is acted upon by several forces, it is acted upon by each of these as if the others did not exist. This is true whether the body is at rest or in motion. In other words, if two or more forces act upon a body at the same time, each produces exactly the same effect as if it acted alone; the total effect or resultant motion of all the forces may be found by a diagram in the same way as the resultant of forces is found.
Page 255 - The resultant of two forces applied at the same point, and acting in the same direction, is equal to the sum of the forces. For example, if the two forces AB and AC, one equal to two and the other equal to three pounds ,are applied at point A, then their resultant AD equals the sum of these forces, or five pounds.
Page 916 - ... instead of 280, the number being reduced because the total movement of the crank, for each indexing, is equal to its movement relative to the index plate, plus the movement of the plate itself when (as in this case) the crank and plate rotate in the same direction. If they were rotated in opposite directions, the crank would have a total movement equal to the amount it turned relative to the plate, minus the movement of the plate.
Page 365 - The principal conclusions to be drawn from the results of this research may be briefly stated as follows: 1. The length of tube, between transverse joints tending to hold it to a circular form, has no practical influence upon the collapsing pressure of a commercial lap.welded steel tube so long as this length is not less than about six times the diameter of the tube.
Page 711 - Rule. — Multiply the diameter of the driving pulley by its number of revolutions per minute, and divide the product by the diameter of the driven pulley.
Page 293 - An externally fired fire-tube or flue boiler is a steam boiler, part of the outer shell of which is exposed to fire or to the products of combustion, and containing flues through which such products pass from the furnace to the uptake.
Bibliographic information
| Title | Machinery's Handbook for Machine Shop and Drafting-room: A Reference Book on Machine Design and Shop Practice for the Mechanical Engineer, Draftsman, Toolmaker and Machinist |
| Contributors | Erik Oberg, Franklin D. Jones, Fred E. Rogers |
| Edition | 5 |
| Publisher | Industrial Press, 1915 |
| Original from | Harvard University |
| Digitized | 3 Apr 2008 |
| Length | 1400 pages |
| Export Citation | BiBTeX EndNote RefMan |