Radford's Cyclopedia of Construction: Carpentry, Building and Architecture, Based on the Practical Experience of a Large Staff of Experts in Actual Construction Work, Volume 2William A. Radford, Alfred Sidney Johnson Radford architectural Company, 1909 - Architecture |
From inside the book
Results 1-5 of 100
Page 62
... inches square , with the inner corner hewn out to receive the lath and plaster . This carries us back to the time of the building of our old home , more than forty years ago . Though only a lad , we remember the time the trees were ...
... inches square , with the inner corner hewn out to receive the lath and plaster . This carries us back to the time of the building of our old home , more than forty years ago . Though only a lad , we remember the time the trees were ...
Page 66
... inch pieces are set in between the studding on a level with the top of the joist . The rough flooring should be laid diagonally with the joist and extend over on to these pieces and nailed . This forms a good tie and makes a closed job ...
... inch pieces are set in between the studding on a level with the top of the joist . The rough flooring should be laid diagonally with the joist and extend over on to these pieces and nailed . This forms a good tie and makes a closed job ...
Page 68
... at right angles to the joist . The side sec- tion should have an extra joist with 7 - inch blocks set in between for the plate or shoe to rest on , so as to form a projection to receive the ends. 68 PRACTICAL CARPENTRY.
... at right angles to the joist . The side sec- tion should have an extra joist with 7 - inch blocks set in between for the plate or shoe to rest on , so as to form a projection to receive the ends. 68 PRACTICAL CARPENTRY.
Page 73
... inches to carry heavy 12 - inch joist , and the joist spaced without any regards for the studding below . While it is true that the joist will probably not break through the plate , still how much better it would be to space the joist ...
... inches to carry heavy 12 - inch joist , and the joist spaced without any regards for the studding below . While it is true that the joist will probably not break through the plate , still how much better it would be to space the joist ...
Page 78
... to this will make 75 inches , or six feet and three inches . In regular two - light windows six inches is allowed for wood or sash in height , two inches top rail , one inch meeting rail and three inches for bottom rail 78 PRACTICAL ...
... to this will make 75 inches , or six feet and three inches . In regular two - light windows six inches is allowed for wood or sash in height , two inches top rail , one inch meeting rail and three inches for bottom rail 78 PRACTICAL ...
Other editions - View all
Common terms and phrases
arch baluster beam bevel Bisect blinds blocks bolts bottom BRACE brackets brick building carpenter ceiling cement chord circle circumference common rafter construction corner cornice curve depth diagonal divide dotted lines draw edge ellipse Engineering equal feet FIGURE finish floor joists four inches give groove gutter horizontal ice chamber illustrates inches inside intersecting jamb join joint king-post laid lath lath and plaster length lintel logs matched boarding method miter mitre box mortar mortise mortise and tenon moulding nailed octagon opening ovolo panel parallel parallelogram perpendicular piece plaster plate polygon purlin radius rail right angles riser roof rowlock sash sash window sheathing shingles shown in Fig shows side sill soffit space span spiked square Steel Square stile stone stool string strip studding tenon thickness timber tread triangle trim truss usually wall weight width window frame wood
Popular passages
Page 17 - The circumference of every circle is supposed to be divided into 360 equal parts, called degrees ; and each degree into 60 equal parts, called minutes ; and each minute into 60 equal parts, called seconds ; and these into thirds, etc.
Page 285 - ... stairs are placed. B shows a portion of a baseboard, the top edge of which has the same finish as the top edge of the string. B and A together show the junction of the string and base. FF show blocks glued in the angles of the steps to make them firm and solid. Fig. 28 shows the manner in which the wall string S is finished at the top of the stairs. It will be noticed that the moulding is worked round the ease-off at A to suit the width of the base at B. The string is cut to fit the floor and...
Page 15 - A convex or concave line is such that it cannot be cut by a straight line in more than two points ; the concavity of the intercepted portion is turned towards the straight line, and the convexity from it.
Page 162 - Code, unless the ashlar be at least eight inches thick and bonded into the backing, and then it may be counted as part of the thickness of the wall. Iron ashlar plates used in imitation of stone ashlar on the face of a wall shall be backed up with the same thickness of brickwork as stone ashlar.
Page 123 - Rule. — Multiply the square of the length in feet by the span in feet, and divide the product by the cube of the thickness in inches; the quotient multiplied by .155 will give the depth.
Page 21 - A Circle is a plane figure bounded by a curved line every point of which is equally distant from a point within called the center.
Page 282 - ... shown, and it will be noticed that they are mitered against a vertical or riser line of the string, thus preventing the end of the riser from being seen. The other end of the riser is in the housing in the wall string. The outer end of the tread is also mitered at the nosing, and a piece of material made or worked like the nosing is mitered against or returned at the end of the tread. The end of this returned piece is again returned on itself back to the string, as shown at N in Fig.
Page 54 - English," which prevailed in this country from about 1189 until 1307. Fig. 58 is the Equilateral arch, the radius with which the arcs are struck being equal to the span of the arch, and the centres being the imposts ; and thus, the crown and the imposts being united, an equilateral triangle is formed. This form was principally used in the " Decorated" period of Gothic architecture from about 1307 until about 1390, at which time the Ogee arch (Fig.
Page 61 - From q, with radius mq, describe an arc cutting the original arc in o. Make mr equal to m o. From o and r, with radius or, describe arcs intersecting each other in i: produce these until they meet the curve p in n.
Page 277 - ... string and riser. Both strings in this instance are open strings. Usually, in stairs of this kind, the ends of the treads are rounded off similarly to the front of the tread, and the ends project over the strings the same distance that the front edge projects over the riser. If a moulding or cove is...